当前位置:首页 > CNC

Arduino CNC Shield V3.XX - 装配指南

watrt5年前 (2019-09-10)雕刻机101060
Arduino CNC Shield V3.XX - 装配指南
这是一个帮助组装Arduino CNC Shield V3.XX的快速指南。我们还有一个讨论论坛:http://forum.protoneer.co.nz/viewforum.php?f = 6内容:对于Grbl v0.9和v1.1 +默认版本:(注意:Z-limit在D12上,主轴使能引脚在D11上使用硬件PWM。)对于禁用可变主轴的Grbl v0.8和v0.9 +,Z-limit移至D11,主轴启用至D12。这通常是为了在旧电路板上向后兼容。对于激光模式,使用的引脚与主轴(PIN 11)相同...

GRBL v1.1版本的限位开关连接

watrt5年前 (2019-09-06)雕刻机26860
GRBL v1.1版本的限位开关连接
     GRBL v1.1版本的限位开关连接wiki翻译Wiring Limit SwitchesSource websit:https://github.com/gnea/grbl/wiki/Wiring-Limit-SwitchesThe limit switchesare used to detect the physical limits of the working area and to position thehead in initial posi...

GRBL如何对刀

watrt5年前 (2019-09-06)雕刻机57450
GRBL如何对刀
对于购买和使用入门级 CNC雕刻机的使用者来说,probing可能会让人产生许多疑问,因为入门级 CNC雕刻机的硬体和软体都未必内建 probing功能。Probing究竟是什么呢?Probing就 CNC雕刻机利用一个 probe(探针 )去探测一个工件 (workpiece)的位置。最简单的 Z轴 probing,雕刻机就可以自动探测到工件表面 (surface)的位置,并把这个位置设置成&n...

Grbl程序使用入门

watrt6年前 (2018-09-04)雕刻机29350
Grbl程序使用入门
Grbl基本操作指令参考【https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.9】  指令码  英文解释中文解释$$View  Grbl settings显示Grbl运行参数配置。$#View  # parameters显示一些特殊G代码需要的参数;有G54~G59的工作坐标偏移量、G28/G30预设置的坐标、刀具长度偏移量、探针偏移等。$GView ...

连接 Grbl

watrt6年前 (2017-12-10)经验20020
连接 Grbl
This wiki is intended to provide various instructions on how to connect to grbl in various ways. Please feel free to contribute more up-to-date or alternative methods.这个维基旨在提供如何以不同的方式连接 Grbl 的各种说明。请随时提供更多最新的或替代的方法。Grbl 的针脚Pin diagram for Grbl v0.8 an...

配置 Grbl

watrt6年前 (2017-12-10)经验30510
配置 Grbl
Grbl has a system ‘$’-command to tweak the settings and trigger runtime commands. Connect to Grbl using the serial terminal of your choice (baud rate 9600 unless you changed that in config.h) as 8-N-1 (8-bits, no parity, and 1-stop bit.) Once connect...